Your location: Home > Products > Coal products >

Fly Ash Dryer

Raw material moisture(%): 15

After drying moisture(%): 1-3

Power(kw): 5.5-18.5×4

Product Introduction:

  Fly ash rotary dryer is also known as the three layers of drum dryer, three return cylinder dryer, on the basis of the single cylinder dryer, developed and manfactured,which is an industrial dryer on non-viscous, liquid material .At present three-cylinder dryer made by Dingli company,with mature technology, throughthe drying of the sand, fly ash, fly, mineral materials, slag and other material , the effect is very good.

fly ash dryer

Product Working Principle:

  The fly ash are conveyed to silo by belt conveyor or bucket elevator ,and transport to the feed end by the feeder of silo .The inclination of the feeding pipeline should be exceed the natural inclination of materials ,so that to facilite sand flowing into the fly ash dryer smoothly .The rotating cylinder of the dryer is slighly inclined to the horizon .To feed the material from the higher end and the heat carrier enter from the lower end ,such produce adverse contact between them .sometimes,they can be fed to the cylinder together .As the cylinder running,the sand carried to the lower side by the gravity.In the process of moving forward ,the wet raw material being roasted by the heat directly or indirectly to make the raw material to dry quickly, the final products discharge out by belt conveyor or screw conveyor..There is shoveling plate installed in the fly ash dryer dryer with function of shoveling the materials up and down,to enlarge the contact area between airflow and materials and to enhance the efficiency and make the material running quickly.The heat carrier is hot air,the flue gas etc.After the dryer process,It need cyclone dust collector to catch the items in the airflow.You should use bag type or wet-type dust collector and afterward discharge the waste gas,if you intend to further reduce the dust load of the exhaust .

Counter flow drying process
Counter flow drying process

concurrent flow drying process
concurrent flow drying process


Product Features:

1. The fly ash dryer is made of alloy steel plate manufacturing,the wear-resisting 3-4 times of ordinary steel , the service life of the equipment is more than 10 years.
2. Material initial moisture content 15%, final moisture to ensure below 0.5-1%,which is the preferred products of the cement plant, GGBS and dry mortar production line.
3. The fly ash dryer thermal efficiency is as high as 80%, at the same time, the total power is low, 40% energy saving.
4. The fuel can be adapted to the fly, oil, gas,it can be dried under 20-40mm particles material, aggregate, powder material.
5. The fly ash dryer covers an area of about 40% lower than single drum dryer and civil investment reduced by about 50%.
6. No air leakage phenomenon, solved the sealing difficulties, modular units, installation is convenient.
7. The discharge temperature is < 50 degrees,which can be directly feed libraries, without cooling.

Technical Parameters:

Model(m) Capacity(T/h) fly consumption
kg/Tdrying materials
Total power
River sand Fly ash Slag
Φ2.0×2 4-5 2-3 3-5 12-14 5.5kw
Φ2.0×4 8-12 4-6 8-10 12-14 3kw×2
Φ2.0×5 12-15 6-7 10-13 10-12 4kw×2
Φ2.2×4.5 14-18 7-9 12-15 10-12 5.5kw×2
Φ2.5×6 23-28 10-13 20-22 10-12 5.5kw×4
Φ2.8×6 30-35 15-18 25-30 10-12 5.5kw×4
Φ3.0×6 35-40 18-20 32-35 8-10 7.5kw×4
Φ3.0×7 40-45 20-25 35-40 8-10 7.5kw×4
Φ3.2×7 45-50 25-30 40-45 8-10 11kw×4
Φ3.2×8 50-55 30-35 45-50 8-10 11kw×4
Φ3.6×8 60-70 35-40 60-65 6-8 15kw×4
Φ3.8×9 70-80 40-45 70-75 6-8 15kw×4
Φ4.0×10 90-100 45-50 80-90 6-8 18.5kw×4
Φ4.2×8.5 80-100 45-60 80-90 6-8 18.5kw×4
(Capacity depend on the raw material moisture is 15% ,and after drying moisture is 1-3%)